Potassium hydroxide generally needs to be used to transport the materials by the conveyor. There is also the need to use the conveyor for the transportation of products when packaging. However, some large blocks may be mixed into the transported materials, so what should be done to avoid the blockage of the conveyor.

我們?cè)谙朕k法避免輸送機出現堵塞情況之前需要了解一下可能會導致堵塞的一些情況，比如說操作的時候沒有按照正確的方法來進行操作那么可能會導致堵塞，還有就是進行輸送的物料輸送過大導致設備負載運轉那么設備再承受不住的時候就可能會導致出現堵塞的情況，所以一般正常情況下使用的時候只需要控制好輸送的氫氧化鉀一般都是不會出現堵塞情況的，不過也是需要避免出現設備空轉沒有物料進行輸送的情況，因?yàn)樵谶@種情況下雖然不會導致出現堵塞的情況，但是會直接的對設備軸承造成比較嚴重的損壞。
 

Before we try to avoid the blockage of the conveyor, we first need to understand some situations that may lead to blockage. For example, if the operation is not carried out in accordance with the correct method, it may lead to blockage. In addition, if the conveying material is too large to cause the equipment to run under load, the equipment may be blocked when it can no longer bear it Therefore, under normal conditions, it is only necessary to control the conveying potassium hydroxide under normal conditions, which will not cause blockage. However, it is also necessary to avoid equipment idling and no material for conveying, because in this case, although it will not lead to blockage, it will directly cause serious damage to equipment bearings.

氫氧化鉀

Potassium hydroxide

而在使用的時候控制好添加物料的輸送其實就是非常重要的，但是其實我們都是知道如果人工進行添加的話這個計量是很不好控制的，所以在這一種情況下我們就可以選擇安裝一個給料器就可以很好的調整添加的計量。

In fact, it is very important to control the transportation of added materials when using. But in fact, we all know that the measurement is difficult to control if we add it manually, so in this case, we can choose to install a feeder to adjust the added metering.

上面介紹的就是氫氧化鉀怎么避免輸送機堵塞，因?yàn)槿绻心骋粋€(gè)部分出現了卡殼其實對于整個流程來書都是會有阻礙的。

What is described above is how to avoid blockage of the conveyor, because if a certain part of the conveyor is jammed, it will hinder the whole process.